Search results for query: forscan

Here's an inexpensive power supply/charger/maintainer that many use for flashing tunes or for module updates (Forscan beta or FDRS). It has a dedicated power supply mode. https://a.co/d/2SkQ7i6 I haven't used it in a while but this one is what a lot of enthusiasts use for long flashing...

...kick on the e-brake any time the vehicle was put into park. Since your vehicle doesn't seem to qualify for the recall (according to your words) i assume it's a 2-bolt differential. That would be why. This is not a configurable option that can be enabled/disabled through ForScan...

...a few mins. I didn't have any issues with the clips on my panel. All in, it took me about 30 mins to do this swap, including time spent on ForScan saving my original modules as_built. But yeah...first time in full sunlight I realized I made a small oops. Maybe i'll try and swap the...

...the cameras in the mirrors, and in the grill. I see the wiring harness for the grill camera in place and connected. I also see an option in ForScan for "360 camera" enable and disable. Mine is set to disable. I know i would need to buy the radio panel with the front cam button as mine...

Thanks folks! I appreciate the information.

No dealer would do it for you either.

Ok, so I need to visit the dealer for them to enable this for me? I see many have it so I just have to try the dealer and see. Thanks for confirming ForScan can’t do it so I don’t waste anymore time looking for it

Config changes take no time at all. Unless you are doing module updates (which few of us are), there is no need for a battery charger/maintainer with Forscan IMHO.

https://www.explorerst.org/threads/updated-forscan-sheet-for-2020-24-ford-explorer-all-trims.7271/page-4#post-116016

...Brane to engage when I park the car everytime via either shifting to park or when I turn the key off. can anyone tell me exactly which ForScan options to change for this? if possible since I don’t have the dash button, can I also get auto brake hold to work when on a hill etc or do I need...

Currently no, this hasn't been resolved for the 25's, or at least it hasn't been made public here. Why wouldn't you just perform the easiest method above? It's easily reversed if you change your mind. Just repeat the steps another time to undo the change. Here's the current Forescan...

I looked around and couldn't find a good answer to this: I have a 2025 ST job 2, and want to setup to use Forscan for a few things documented in this forum. This Post , talks about using a Battery tender/maintainer while using Forscan. While this other post states to use a good battery...

Wait, so all you did was make those changes and somehow you got start/stop disabled? Are you sure you didn’t change anything else? I would love to disable mine.

Is there an actual way to do this is forscan on the 2025’s?

I believe this is the one from the FORScan website - OBDLink EX FORScan OBD Adapter

What OBDII device are you using?

...notice that some of the modules do not load. Such as the APIM......cannot seem to find it. I was using an OBDII connector that wasn't the one FORScan says to use. So I ordered the one recommended on the site and while it seemed to give me a couple less "yellow" flags, it did tell me that my...

I'm in the same boat, there are a couple of youtube videos that I found helpful.

Thank you for this! I need a little help though… I want to correct the tire circumference for my 2022 Explorer in FORScan due to new 305/40/22 tires (31.6” diameter, 99.2” circumference, 638 rev/mile). I’m editing 726-15-01 and 726-15-02. Converted 99.2” to ~2520 mm (0x09D8 hex), and plan to...

...the interior displays and backlighting using the headlight control panel. Additionally, you can enable Silent mode in the BCM and APIM using Forscan, which will give you a "Silent Mode" option in Sync under vehicle settings. Silent mode disables all exterior lighting/most interior lighting...