R2D2's 2022 ST - KISS Build

R2D2 · May 6, 2023

FORScan Changes on my ST

Setup details

Double Horn Honk on Leaving Cabin
Using Front Fog with High Beam
Power Point Timeout
Remote Global Close
Auto Start Stop Disable (PSCM method - Not working)
Silent Mode Control Function
Disable Chimes Seat Belt Minder
Disable three start-up chimes
Reverse Mirror Tilt
Amber DRL with/without White DRL
Auto Start Stop Disable (BMS method - Not working)
Engine Sound Enhancement Delete
Auto Rear Wiper on Reverse

R2D2 · May 6, 2023

FORScan Change: Double Horn Honk on Leaving Cabin

Module : BdyCM - Body Control Module
Method: Easy click select (not As-Built)
Status: Done Successfully

R2D2 · May 7, 2023

FORScan Change: Using Front Fog with High Beam (Bambi mode)

Module : BdyCM - Body Control Module
Method: Easy click select (not As-Built)
Status: Done Successfully

R2D2 · May 7, 2023

FORScan Change: Power Point Timeout, s (12V outlet after ignition off)

Module : BdyCM - Body Control Module
Method: Easy click select and enter value in seconds (not As-Built)
Status: Changed to 360 sec from 3600 sec
Issues: None.
Working as intended. All the charging and power ports gets 6 mins timeout as I have set. (All three 12V sockets and 2USB charging ports for second row.)

The two data/power USB ports in the front and the house hold outlet in the second row, loses power with ignition off, immediately. Not sure if it was like that earlier (before I made the change).

R2D2 · May 7, 2023

FORScan Change: Remote Global Close

Module : BdyCM - Body Control Module
Method: Easy click select multiple options (not As-Built)
Status: Did not work
Plan: Need to try As-Built method, with multiple module changes, to figure out this one.

Plan Worked : 05/07/2023
Method: As-Built Modules BdyCM, DDM, PDM, AIPM
Status: Working successfully

Working : Now both front windows can be opened and closed from the remote.

Changes made (in green boxes) as below: Red boxes has the old values

R2D2 · May 7, 2023

FORScan Change: Auto Start Stop Disable

Module : PSCM - Power Steering Control Module
Method: As-Built Data change to 730-03-01 xxxx xxxx 00--

Status: ASS seems to be disabled. ASS came back after few miles.
Issues : Showed multiple system errors. I restored back factory settings. Errors are gone but the proximity sensors sound different now. ASS is still disabled.
Plan: Need to drive for sometime to understand all the changes. Happy that ASS is disabled but not happy that it changed other things.
Known Cons: the ASS physical switch will not work and any changes need to be done with FORScan only.
Other Solution: buy the 100$ ASS eliminator circuit and install the hardware solution.

I have read that many here has already done it, do enlighten me what am I missing? The before and after values you have changed will be really helpful.

Tried something else ( see below post # 53)

Max Salvo · May 8, 2023

I have a 22 ST as well. The info on Forscan was very helpful. Thanks for taking the time and effort to put this together.

Ive searched without success to find out how you can disable the exterior lights from coming on each time you open a door. Ive disabled the headlights through the normal dash settings but the daytime running lights and other exterior lights still come on. Very annoying when at the drive in theater with the family or arriving to your deer hunting spot before sunup and the vehicle lights up like a Christmas tree every time you open a door. Ive found mentions of police mode, dark mode, silent mode but nothing concrete for this exact vehicle. Anyone turned these off successfuly on a 22 ST and willing to share the settings? Thanks

Nine29 · May 8, 2023

R2D2 said:

FORScan Change: Power Point Timeout, s (12V outlet after ignition off)

Module : BdyCM - Body Control Module
Method: Easy click select and enter value in seconds (not As-Built)
Status: Changed to 360 sec from 3600 sec
Issues: 12V power is cut immediately with ignition off, rather than the 6 min set by me.

View attachment 17779

Which powerpoint(s) does this change?

scoobysportD · May 8, 2023

R2D2 said:

This should get a sticky thread on its own somewhere, thanks for the clear writeup!

R2D2 · May 8, 2023

Max Salvo said:

I have seen it for f150 and the dark mode and silent mode should work for explorer as well. Only issue is that it's enabled with forscan only, for Sync 3.x systems. For Sync 4 you can get an easy toggle switch on the screen. Makes it much easier to adjust it on the go.

Will keep an eye out for what can be done for ST, but I don't have an answer right away.

R2D2 · May 8, 2023

Nine29 said:

Should be for all of them, 12V ones in the front and back, all USB ones and the household one for the second row.

I have only tested it for the 12V inside the arm rest console, for my dashcam. Will check the other ports and confirm.

R2D2 · May 8, 2023

R2D2 said:

Nine29 said:

All the charging and power ports gets 6 mins timeout as I have set. (All three 12V sockets and 2 USB charge only ports for second row.)

The two data+power USB ports in the front and the house hold outlet in the second row, loses power with ignition off, immediately. Not sure if it was like that earlier (before I made the change).

R2D2 · May 9, 2023

FORScan Change: Auto Start Stop Disable

Module : PSCM - Power Steering Control Module
Method: As-Built Data change PSCM 730-01-02 xxxx xxxx 01--

00=Auto Start/Stop Disabled

01=Auto Start/Stop Enabled, Angle Inhibit Enabled

02=Auto Start/Stop Enabled, Angle Inhibit Disabled

Since my initial value was already 00, I have tried 01.
original values in Red box, changed values in the Green box.

Status : ASS is disabled in D, in Normal mode.
Issues : Reverse Brake Assist disabled in R

Plan: Try to run this for some time and see if ASS returns. If not, leave it as is, and live without Reverse Brake Assist. I feel the solution is better than the one that disables BMS.
I might go into a hardware solution later.

R2D2 · May 9, 2023

FORScan Change: Silent Mode Control Function (Dark Car mode)

Module : APIM Module
Method: Easy click select
Status: Done Successfully. Toggle button gets enabled in the Sync 3.4 and above

Thanks @Max Salvo for asking about it. Its so easy to do in Sync 3.4 and above.
I will keep this option off almost all the time, though. Who doesn't like the Christmas light show.

Max Salvo · May 10, 2023

R2D2 said:

Thanks a million for this. As soon as I get some time I will use your instructions and make the changes. I wasnt expecting to get a toggle button so thats a happy surprise. Thanks again for posting everything in this thread.

Nine29 · May 10, 2023

R2D2 said:

Thanks...just what I needed to know! Do you know what value to use if you want them to stay powered permanently?

bhunted1 · May 10, 2023

R2D2 said:

FORScan Change: Silent Mode Control Function (Dark Car mode)

Module : APIM Module
Method: Easy click select
Status: Done Successfully. Toggle button gets enabled in the Sync 3.4 and above

View attachment 17827

View attachment 17828

Thanks @Max Salvo for asking about it. Its so easy to do in Sync 3.4 and above.
I will keep this option off almost all the time, though. Who doesn't like the Christmas light show.

Just tried this. I dont get the option button. Any thoughts?

R2D2 · May 10, 2023

Nine29 said:

Not sure about permanent on, but seen As Built, change to 18 hours (18*60*60 value in that field). No harm in trying a bigger number there.

I would not do it, as it puts the battery under lot pressure and can end up with a dead battery.

bhunted1 said:

Did you cycle the ignition properly, after write?
What I do is write the change first. Then when it asks for switching the ignition on and off, I will also open and close the driver door for full vehicle systems shutdown and reboot.

Also I have the latest software, in terms of sync, adaptor drivers and FORScan.

Then again, some forscan changes can revert back like the auto start stop. And this varies with different model years of the same vehicle. I would try it one more time, as this was very straight forward and easy change in my case.

bhunted1 · May 10, 2023

Yep, sop. I have a 2023 and no prob with the ass switch being off. I usually change the as-built after making a backup of the module.

Did you do a reboot as in reboot the screen or you just mean shutting vehicle off etc.?

Sent from my iPhone using Tapatalk

bhunted1 · May 10, 2023

Ok, came back out after lunch and it was avail. Did you actually try it to see if it works?

Sent from my iPhone using Tapatalk

Sign Up! To view all forums and unlock additional cool features

R2D2's 2022 ST - KISS Build

Member

Member

Member

Member

Member

Member

New Member

Member

Member

Member

Member

Member

Member

Member

New Member

Member

Member

Member

Member

Member